Vermont-casting 1610 Manuel d'utilisateur télécharger pdf (Page 32)

Defiant 1610 Non-Catalytic Woodburning Stove

30002850

Adjust the Damper as Needed

The tension on the Deﬁant’s damper is adjustable to

compensate for compression of the gasket that seals

the damper to the upper ﬁreback. To adjust the damper:

1. Remove the griddle. Loosen the lock nut at the cen

ter of the damper. (Fig. 39)

2. Turn the pressure screw approximately one half turn

clockwise with an Allen wrench provided with your

stove.

3. Tighten the lock nut. Prevent the pressure screw

from turning as you tighten the nut. Re-test the

damper.

Tighten the Damper Handle as Needed

A handle on the left side of the stove controls the

damper. The handle attaches to the damper rod with a

set screw. Periodically check the set screw and tighten

as necessary.

How to Adjust the Door Latches

The Deﬁant’s doors should close securely to prevent

accidental opening and to keep air from leaking into the

stove. On properly adjusted doors, the handles should

resist slightly as they are turned to the closed position

and the doors themselves should be drawn slightly

toward the stove.

Over time, the gasket around the doors will compress

and the latches may need adjustment.

To adjust the latches, loosen the small lock nut, rotate

the striker screw a half-turn, and re-tighten the small

lock nut. (Fig. 40) Your stove kit includes an Allen

wrench for latch adjustments. Hold the striker screw to

keep it from turning as you tighten the lock nut. Make

repeated small adjustments until the setting is right.

Replace the Stove Gaskets as Needed

Your Deﬁant uses ﬁberglass rope gaskets to make

a tight seal between some parts. With use, particu-

larly on moving parts, gaskets can become brittle and

compressed and can begin to lose their effectiveness.

These will need periodic replacement.

The sizes of replaceable gasket are listed below, along

with their applications.

Gasket Diameter... ...And the Parts it Seals

5/16” The griddle to the stove top

(wire reinforced gasket)

5/16” The damper to the upper ﬁreback; the

front doors to the stove front; and the

doors to each other.

3/8” The ash door to the front of the bottom

panel

3/16” The outer glass panes to the door

If you need to change a gasket, ﬁrst obtain an appropri

ate replacement from your Vermont Castings, Autho-

rized Dealer.

Wait until the ﬁre is out and the stove has cooled. Be

sure to follow the standard safety procedure for working

with dusty materials: wear safety goggles and a dust

mask.

The procedure for replacing gaskets is the same,

regardless of the gasket location. Follow these eight

steps:

1. Remove the existing gasket by grasping an end and

pulling ﬁrmly. (Fig. 41)

2. Use a wire brush or the tip of a screwdriver to clean

the channel of any remaining cement or bits of gasket.

Remove stubborn deposits of cement with a cold chisel

if necessary. (Fig. 41)

ST531

Door Pawl

11/00

Pawl

Small Lock-

ing Nut

Large

Locking

Nut

Set Screw

Striker Screw

Handle Stub

ST531

Fig. 40 Turn the door latch striker screw in or out to tighten or

loosen the screw.

ST554

Damper adjustment

11/00

Pressure Ad-

justing Screw

Allen

Wrench

Lock Nut

Damper

ST554

Fig. 39 Adjust the damper with the Allen wrench.

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 38 39 40

Commentaires sur ces manuels

Pas de commentaire

Vermont-casting 1610 Manuel d'utilisateur Page 32

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Vermont-casting 1610